The aim of this blog is to connect fly-tyers all over the world, to share, techniques, patterns, information and knowledge.

Cottus Gobio

IMG_6281

Hook: Mustad R 74 # 2

Thread: Dyneema

Tail: Siberian squirrel tail hair

Body : Squirrel tron dark hares ear dubbing

Rib: Fine copper wire

Wing: Pine squirrel zonker strip

Collar: Natural red fox body hair spun in dubbing loop

Gill covers: 2 Ring neck pheasant “church window” feathers coated with Bug Bond

Head: Natural kangaroo body hair spun in dubbing loop and clipped to shape

Eyes : Epoxy eyes

The original zonker pattern was tied by the American fly tyer Dan Byford in the 1970s and was quickly recognized the world over, as a big fish fly and extremely easy to tie, yet a realistic imitation for most smaller bait fish. The original pattern used a lead or tin sheet that was folded and glued over the hook shank and then cut to shape to make the underbody.   The flexibility of the Zonker as a bait fish imitation pattern is only limited to your own imagination. There are a huge amount of rabbit fur strip materials on the market in just about every colour imaginable, not to mention fox, squirrel, mink etc, the combination possibilities are endless. Another advantage with the zonker, unlike buck tail and feather wing streamers, is that it is an extremely robust pattern. If tied correctly the fly will normally outlive the hook, although the eyes are somewhat vulnerable to the small sharp teeth of trout. This can be improved by attaching the eyes with super glue and coating them with Bug Bond or head cement.

When fishing this pattern or any long tailed streamers in general for that matter. Many fly fishermen are of the thought, that when fishing a long tailed streamer the fish tend to “Nap” at the tail and won´t take the fly properly! This can be the case for smaller trout but generally speaking a large trout will take this pattern hard and fast. If you do experience napping at the tail when fishing, stop the retrieve dead, and let the fly sink a little for two or three seconds, nine times out of ten the attacking fish will pick it up on the drop.

1Secure your Mustad R 74 # 2 hook horizontal in the vice.

1
Secure your Mustad R 74 # 2 hook horizontal in the vice.

IMG_6240

3
Cut a good bunch of Siberian squirrel tail with clear markings. Stack the hair and tie in for the tail. The tail should be approximately the same length as the hook shank. If you would like to add weight to your fly, this is the time to do it.
IMG_6241

4
Now tie in a length of medium copper wire, at the tail base for the rib.

IMG_6242

5
Dubb your tying thread with dark hares ear Antron dubbing and start making the body of the minnow.

IMG_6243

6
Once you have wound the dubbing forward in a tapered body, about one cm from the hook eye, brush out the fibers with a tooth brush. This will give more body and movement to the finished streamer.

IMG_6244

7
Cut a zonker strip from a pine squirrel hide. Make sure that the strip is tapered to a point at the tail of the strip.

IMG_6245

8
Again try and choose a squirrel strip that has nice markings and a good taper.

IMG_6246

9
Place the zonker strip up on top of the body of the fly so that it´s the same length as the tail. Now wind on the copper wire rib.

IMG_6247

10
Take care not to trap the fibers of the squirrel as you go. There should be no more that six turns of copper wire between the tail base and the end of the body.

IMG_6248

11
Once you have reached the end of the body tie off the copper wire and the zonker strip. Remove the excess and tie down.

IMG_6250

12
Now place a strip of natural red fox body hair still on the hide in a paper clip or the Marc Petitjean magic tool as used here.

IMG_6253

13
Make a dubbing loop an spin the fox hair into a dubbing brush.

IMG_6254

14
Wind on the fox dubbing brush making sure that you comb the hair back and up with each turn, this will form the over wing of the streamer. If you have some fox hair that has accumulated on the underside of the throat trim this away, this same depth as the body.

IMG_6259

15
Now select two ring neck pheasant church window feathers, the same size. Coat these with Bug Bond.

IMG_6261

16
Now tie these in, concave out, as shown. One each side to form the fins. These also give a wobbler effect on the streamer when fished.

IMG_6263

17
Make another dubbing loop. Here I have used natural kangaroo body hair. If you dont have kangaroo you can use another coarse natural hair.

IMG_6264

18
Now wind on the dubbing brush forward tight into the rear of the hook eye. Again taking care not to trap and tie down the hair as you go.

IMG_6266

19
Whip finish. Before you begin to trim and form your streamer head, brush out the fibers with a tooth brush to open the hair and give more volume. Trim the head to shape.

IMG_6267

20
Select two epoxy fly eyes, these should be a little larger than the natural for the size of the streamer. This will give a slightly more efficient attractor factor.

IMG_6269

21
The finished streamer.

2 responses

  1. Such a nice streamer!
    Well done!
    I will try to make this one for perch and pike in The Netherlands.
    Thanks for sharing this with us.
    I like your style.
    greetings and tight lines
    René

    October 2, 2013 at 10:18 pm

    • Thanks Rene, good luck and tight lines!

      I tie at the Dutch fly fair so if you are around for the next one pop in and say high.

      Barry

      October 4, 2013 at 9:29 am

Leave a Reply

Please log in using one of these methods to post your comment:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s