Cottus Gobio
Hook: Mustad R 74 # 2
Thread: Dyneema
Tail: Siberian squirrel tail hair
Body : Squirrel tron dark hares ear dubbing
Rib: Fine copper wire
Wing: Pine squirrel zonker strip
Collar: Natural red fox body hair spun in dubbing loop
Gill covers: 2 Ring neck pheasant “church window” feathers coated with Bug Bond
Head: Natural kangaroo body hair spun in dubbing loop and clipped to shape
Eyes : Epoxy eyes
The original zonker pattern was tied by the American fly tyer Dan Byford in the 1970s and was quickly recognized the world over, as a big fish fly and extremely easy to tie, yet a realistic imitation for most smaller bait fish. The original pattern used a lead or tin sheet that was folded and glued over the hook shank and then cut to shape to make the underbody. The flexibility of the Zonker as a bait fish imitation pattern is only limited to your own imagination. There are a huge amount of rabbit fur strip materials on the market in just about every colour imaginable, not to mention fox, squirrel, mink etc, the combination possibilities are endless. Another advantage with the zonker, unlike buck tail and feather wing streamers, is that it is an extremely robust pattern. If tied correctly the fly will normally outlive the hook, although the eyes are somewhat vulnerable to the small sharp teeth of trout. This can be improved by attaching the eyes with super glue and coating them with Bug Bond or head cement.
When fishing this pattern or any long tailed streamers in general for that matter. Many fly fishermen are of the thought, that when fishing a long tailed streamer the fish tend to “Nap” at the tail and won´t take the fly properly! This can be the case for smaller trout but generally speaking a large trout will take this pattern hard and fast. If you do experience napping at the tail when fishing, stop the retrieve dead, and let the fly sink a little for two or three seconds, nine times out of ten the attacking fish will pick it up on the drop.
- 3
Cut a good bunch of Siberian squirrel tail with clear markings. Stack the hair and tie in for the tail. The tail should be approximately the same length as the hook shank. If you would like to add weight to your fly, this is the time to do it.

6
Once you have wound the dubbing forward in a tapered body, about one cm from the hook eye, brush out the fibers with a tooth brush. This will give more body and movement to the finished streamer.

7
Cut a zonker strip from a pine squirrel hide. Make sure that the strip is tapered to a point at the tail of the strip.

9
Place the zonker strip up on top of the body of the fly so that it´s the same length as the tail. Now wind on the copper wire rib.

10
Take care not to trap the fibers of the squirrel as you go. There should be no more that six turns of copper wire between the tail base and the end of the body.

11
Once you have reached the end of the body tie off the copper wire and the zonker strip. Remove the excess and tie down.

12
Now place a strip of natural red fox body hair still on the hide in a paper clip or the Marc Petitjean magic tool as used here.

14
Wind on the fox dubbing brush making sure that you comb the hair back and up with each turn, this will form the over wing of the streamer. If you have some fox hair that has accumulated on the underside of the throat trim this away, this same depth as the body.

15
Now select two ring neck pheasant church window feathers, the same size. Coat these with Bug Bond.

16
Now tie these in, concave out, as shown. One each side to form the fins. These also give a wobbler effect on the streamer when fished.

17
Make another dubbing loop. Here I have used natural kangaroo body hair. If you dont have kangaroo you can use another coarse natural hair.

18
Now wind on the dubbing brush forward tight into the rear of the hook eye. Again taking care not to trap and tie down the hair as you go.

19
Whip finish. Before you begin to trim and form your streamer head, brush out the fibers with a tooth brush to open the hair and give more volume. Trim the head to shape.

20
Select two epoxy fly eyes, these should be a little larger than the natural for the size of the streamer. This will give a slightly more efficient attractor factor.
This entry was posted on December 18, 2012 by barryoc. It was filed under Fly Fishing art, Fly Tying, Material Reviews, Step by Step and was tagged with Brown trout, Bug Bond, Fly Tying, hooks, Materials, Step by Step, streamer, Streamers, Zonker.
2 responses
You must log in to post a comment.
Such a nice streamer!
Well done!
I will try to make this one for perch and pike in The Netherlands.
Thanks for sharing this with us.
I like your style.
greetings and tight lines
René
October 2, 2013 at 10:18 pm
Thanks Rene, good luck and tight lines!
I tie at the Dutch fly fair so if you are around for the next one pop in and say high.
Barry
October 4, 2013 at 9:29 am