The aim of this blog is to connect fly-tyers all over the world, to share, techniques, patterns, information and knowledge.

FisHeadz Mackerel

Mackerel 1

Back to the tying bench again, this time with a salt water pattern. I must say, Its nice to see that salt water materials being made in smaller sizes, not just for the monster warm water fish across the pond. These FisHeadz from Deer creek in the UK , are perfect in the two smallest sizes for salt water fishing in Europe, for both bass in the south and sea trout here in the North.

IMG_9699

I still haven’t had much time to play with these, I’v only tied half a dozen flies with them, but they are that easy to use, that I’v been relatively pleased with all of them, which is unusual ! Anyway if you are tying salt water patterns you have just got to give these a go they give the flies a real edge. But beware, one of the flies I tied wasn’t up to par, and when I came to attach the fisHeadz, it was like putting lipstick on a gorilla!  Without doubt it would still catch fish, but if you want flies tied with fisheadz to look good, the rest of the fly has to be as good as the headz.

This is an extremely quick pattern to tie, the only thing you really have to be careful with is the proportions and quantities of materials.

Hook: Mustad 60004NP-NZ # 12 http://www.mustad.no/productcatalog

Tying thread: Dyneema http://www.virtual-nymph.com/index.php?option=com_virtuemart&page=shop.browse&category_id=1&Itemid=26

Wing: Ultra hair and buck tail

Sides: Blue grizzle hackle

Head: Deer Creek Blue jay sand eel headz http://www.deercreek.co.uk/FISHEADZ-tm.html coated with Bug Bond http://www.veniard.com/section188/

IMG_0196

1

Secure your salt water hook in the vice.

IMG_0198

2

Take about 10 strands of transparent Ultra hair and tie in, about three times the length of the hook shaft. This stiffer synthetic hair will give the wing of the fly support and structure.

IMG_0199

3.

Now cut a small bunch of straight white buck tail, you only need about 15 strands, this will give the wing a little more volume but keep it light and mobil when it swims. Remove all the underfur and shorter hairs from the bunch. I didn’t stack this hair because I wanted the very tail of the pattern to be broken up, and not too uniform. Tie this in on top of the Ultra hair.

IMG_0200

4.

Now select two dyed blue grizzle hackles and prepare by stripping off the base of the stems and cutting both down to the correct length. Tie in one each side over the under wing.

IMG_0201

5.

Place your Fisheadz one each side in the correct position, they are sticky backed so they will stay there. Once right just make a couple of turns of tying thread to hold them steady.

IMG_0202

6.

Whip finish and remove the tying thread. Give the whole head a coat with Bug Bond and cure with the UV light.

IMG_0211

7.

For the last stage I have added additional hi-viz tape eyes, just to give the head a little more three dimensional feel, if thats possible?

IMG_0171

 

Heres a sand eel tied with FisHeadz.

6 responses

  1. Great looking pattern. In other colors, it could imitate other important bait fish. Only addition I might suggest is a short loop of stiff mono above the bend before tying in any of the materials, to keep that long body/tail from fouling the hook.

    February 7, 2013 at 9:16 pm

    • Hi Gary, Thanks, Yeah with softer materials I normally put a extended support loop of mono, but the under wing of this is Ultra hair which is a stiff crimpped nylon. Although I only tied this today and have never fished with it, I think it would be ok.

      February 7, 2013 at 10:04 pm

    • Barry, you might be right. And I haven’t yet tied it at all. Trying to find out if Fish Headz are available in the U.S.

      February 8, 2013 at 1:16 am

    • I think the best way to find out is pay their wesite a visit the link is in the article Gary.

      February 8, 2013 at 9:29 am

  2. Really glad to come across this site. So much information and easy to follow tutorials.

    Do you happen to remember what size of Fish Headz were used on this fly?

    Thanks so much!

    October 4, 2013 at 7:36 am

    • Hi Jared, Thanks for the kind words.
      The head on this pattern is about 2 cm long. I dont have exact sizes because they just came to me eith a whole load in a packet without info. But they come in lots of sizes from about 1 cm – 5 or 6 cm for larger patterns.

      Cheers

      Barry

      October 4, 2013 at 9:27 am

Leave a Reply

Please log in using one of these methods to post your comment:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s