The aim of this blog is to connect fly-tyers all over the world, to share, techniques, patterns, information and knowledge.

Another CdC tutorial with Marc Petitjean

C-Bickel-LD_2

Charles Bickle one of the pioneers of CdC flies, standing on the bank of the Orbe river in Switzerland in the town of Vallorbe in the 1920s.

IMG_6455

While visiting Marc at his home, although a little more overgrown, we managed to find the same spot on the river where the famous Bickle developed and fished the first CdC patterns.

After a weekend with Marc Petitjean we managed to do a little fishing, although the conditions where not perfect and there was little activity in our local forest lakes, we did manage to make a few more tutorials.

This first one, is one of Marc’s quick and easy CdC bead head nymphs. When Marc began tying nymphs with CdC ( nearly 20 years ago) many prominent anglers thought it was a joke! and that CdC was not a suitable material for nymphs, oh how time has proved them wrong. Over the next few weeks I will be posting several articles on Marc Petitjean patterns and his ingenious tools and how to use them.

IMG_72191

Place a bead head on the nymph hook and secure in your vice with the hook shank horizontal.

IMG_72202

Wrap a short length of lead wire, enough to go into the bead head.

IMG_72213

Using your nail push the wraps of lead wire into the bead head opening.

IMG_72224

Attach your tying thread and make a few turns to hold the lead wire in place in the bead head and then wrap it back towards the hook bend.

IMG_72235

Select three CdC hackles of your colour choice approximately the same length. The choice of colours will determine the colour of the twisted segmented finished body, that has an almost woven effect.

IMG_72246

Tie in the ends of the CdC hackles as shown.

IMG_72257

At the very end of the hackles attach the Petitjean hackle plier. This technique can only be done successfully with Marc’s plier, it does not slip, even with three hackles in it!

IMG_7226

8

Now trim off the hackle shaft ends, close to the pliers.

IMG_7227

9

Now wind your tying thread forward about 2/3 of the hook shank. Take the pliers and twist the CdC only about three times. If you twist it more you will break the CdC hackle stems.

IMG_722810

Begin wrapping the twisted CdC to form the body of the nymph. Marc calls this Twist and Wrap but only one twist for each wrap. Continue until you reach the tying thread.

IMG_722911

Tie off the CdC hackles.

IMG_723112

Trim off the excess CdC hackle stems behind the bead head.

IMG_723213

Carefully trim off the CdC fibers around the whole body of the nymph.

IMG_723314

The trimmed body.

IMG_723515

Now for the nymph legs. You dont need too much CdC fibers for this so remove the fibers from one side of the hackle.

IMG_728116

Place a small amount of Petitjean ice dub over the jaws of the smallest magic tool.

IMG_728217

Take the prepared CdC hackle.

IMG_728318

Holding the hackle with both hands pull it down on top of the ice dubbing and into the jaws of the Magic tool.

IMG_728419

Now the hackle and dubbing should be in place in the jaws of the Magic tool.

IMG_728020

Now trim off the CdC ends on each side of the Magic tool jaws. This is very important or the hackle will be caught in the magic tool spring when you try and remove it.

IMG_723821

Transfer the hackle and dubbing to the magic clip tool and with straight scissors cut of the hackle stem.

IMG_724022

Put your loaded magic clip to one side and make a dubbing loop to spin the CdC in.

IMG_7241

23

If you are using the Petitjean bobbin holder you can make the loop like this.

IMG_724224

While holding the loop open with your finger push the bobbin end into the loop as shown.

IMG_724325

Remove your finger and rest the loop on the bobbin.

IMG_724526

Slide the thread up the bobbin and as it recovers to a vertical position the loop will catch on the bobbin dubbing loop hook and hang there.

IMG_724627

Open the loop with one hand and offer up the loaded magic tool.

IMG_724728

Place the fibers of CdC and ice dubbing in the loop and remove the magic tool clip.

IMG_724829

The material should be now trapped in the loop.

IMG_724930

Twist the bobbin and spin the material into a dubbing brush.

IMG_725131

You can now wind on the dubbing brush to form the legs of the nymph.

IMG_725832

Once the dubbing brush is completely wound on tip your bobbin as shown.

IMG_725933

If you slowly increase the angle of the bobbin the loop will slide off the dubbing loop hook on the bobbin as shown here.

IMG_726034

Make a couple of turns of tying thread just to secure the loop end behind the bead head.

IMG_726235

Trim off the remaining loop end.

IMG_726336

You can now whip finish the nymph tight into the bead head.

IMG_726737

Remove the tying thread and you have your finished bead head CdC nymph.

6 responses

  1. David T

    That’s an extreemly good ‘generalist pattern’… Like it a lot!!

    May 27, 2013 at 4:40 pm

    • Thank you David. i will be posting more from Marc soon.

      May 27, 2013 at 6:12 pm

  2. Pingback: Fly Tying Step-by-Step Tutorial: Marc Petitjean’s CDC Nymph « the limp cobra

  3. Hey i fish the lower niagara river wloihporl for steelhead and browns. I like using slip bobbers and other meathods, could you give me fly suggestions slip bobber fishing? Thanx>>>>>>>>>>> Lou P.

    August 9, 2013 at 3:04 pm

  4. I’ve seen serval ocoebtr caddis patterns, but this 1 I like a lot, simple, easy to tye, & the materials are readily available,I might add a rootbeer krystal flash antennae just because I like antennae.

    September 1, 2013 at 9:51 pm

  5. Holy shiznit, this is so cool thank you.

    October 30, 2013 at 5:27 am

Leave a Reply

Please log in using one of these methods to post your comment:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s